ga('set', 'userId', {{USER_ID}}); // Set the user ID using signed-in user_id. Starrett-sr100
724 368-8006
Rapp Industrial Sales Surface Finish Equipment
Mahr Pocket Surf IVMahr M1 - M2Mahr Pocket Surf PS1Mahr M300Mahr M300CMitutoyo SJ-410Mitutoyo SJ-210Mitutoyo SJ-310SRG-4000SRG-2000SPIStarrett SR100Starrett SR200Starrett SR300/400Reference StandardsFlexbar MetrologyTesa Rugo surf 10GTesa Rugo surf 20Tesa Rugo surf 90GCalibrationRepairAbout usSRG-4500Mahr S2Fowler XProStarrett SR160 Products
The SR100 shown below has been discontinued. The new replacement model is the SR160 model.
Many of the SR100 units in the field still have life in them but need repaired,our repair department can handle your repairs.
EASY-TO-USE & ACCURATE
The SR100 portable surface roughness tester is powerful, accurate and easy to use.
With the SR100, you can measure roughness almost anywhere. It is ideal for checking large components, structures, auditing batch production prior to shipment and production line process control.
Separates into Two Pieces
The innovative SR100 separates into two pieces to measure surface roughness. The bottom half contains the traverse mechanism and stylus pick up assembly. This is placed on the surface to be measured. It has a wide base to ensure stability.
The upper half includes the large LCD display, start button, mode and parameter buttons, comfortably hand held for easy operation and clear viewing.
How it does it
A diamond stylus is drawn across the part. The motorized traverse mechanism is cam driven to ensure that the correct horizontal distance is traveled.
Vertical movement of the stylus as it travels across peaks and valleys is detected by a piezo-electric pick up which converts mechanical movement into an electrical signal.
The electrical signal is digitized and sent to a microprocessor where the parameters are instantly calculated using standardized algorithms.
Features
*Large LCD window
*Measures Ra at the touch of a button
*In addition to basic roughness parameter Ra and Rz, also measures advanced Rp, Rv, and Rt parameters
*five second cycle time
*Result saved until the next measurement is taken
*Switches between inch and metric mode without remeasuring
*Use right out of the box-little or no operator training required
*Automatic shut-off after five minutes of inactivity
*Configured with the most common industrial settings to ensure correlation between multiple operators (see specifications)
*Simple and reliable calibration routine
*Uses standard off-the shelf calculator type batteries with a minimum life of 5,000 measurements
*Includes SR100 two-piece assembly, calibration standard, batteries, operation guide and a carrying case
Technical Specifications | ||||||||||||||||||||||||||||||||||||
Gauge range | 200µm (0.008in) | |||||||||||||||||||||||||||||||||||
Accuracy | 5% of reading + 0.1µm (4µin) | |||||||||||||||||||||||||||||||||||
Pick up type | Piezoelectric | |||||||||||||||||||||||||||||||||||
Gauge force | .007 oz. | |||||||||||||||||||||||||||||||||||
Stylus | Diamond, Radius 5µm (200µin) | |||||||||||||||||||||||||||||||||||
Cut off value | 0.03in + 15% | |||||||||||||||||||||||||||||||||||
Filter | 2CR | |||||||||||||||||||||||||||||||||||
Traverse length | 5mm (0.2in) | |||||||||||||||||||||||||||||||||||
Traverse speed | 0.08in/sec | |||||||||||||||||||||||||||||||||||
Display unit | µm / µin | |||||||||||||||||||||||||||||||||||
Battery life | 5,000 operations minimum | |||||||||||||||||||||||||||||||||||
Parameter Results | ||||||||||||||||||||||||||||||||||||
Code 112/3115-01 | Ra, Rz, Rv, Rp, Rt
|
SR100 Surface Roughness Tester & Accessories
Cat. No. EDP
SR100 20950 SR100 two-piece surface roughness tester assembly,
calibration standard, batteries, operation guide and a
carrying case.
724-368-8006 * Fax 724-368-8005